Allen-sports 103AB Bedienungsanleitung PDF herunterladen

Allen

Model103A Bike Rack

English Instructions

Pg. 1

Mounting rack on vehicle:

Caution: Use Allen 103A only in accordance with local motor vehicle and traffic regulations.

• To avoid damage to rear door or trunk, do not open trunk or rear door when hooks or rack are in place.

• Install rack and load bicycles only at a safe distance away from moving traffic.

•

Only rubber feet and hooks should come into contact with car. Do not allow metal parts of rack or bicycles to

scratch car’s finish.

• Make sure that all of rack and bicycles are kept at a safe distance from road and hot exhaust.

• Remove rack from car when not in use.

WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury - do not use

rack on any vehicle on which it can not be properly mounted as described in this instruction sheet.

• Top hooks must be completely hooked over solid metal edges at top/front of trunk lid or rear door - never hook

to rain gutters, roof racks, vertical rear glass, rubber or plastic moldings.

• Mount rack only with bottom feet on a rigid surface of car (never on glass), and with bottom foot assembly

completely extended. Never use on trailers or front of vehicle.

•

Never carry more than 3 bikes (max. capacity: 100 lb.) - no tandems, mopeds, or recumbents. Bikes must be securely tied

to rack - use individual bike tie-down straps or additional straps if necessary. Car tail lights must remain visible.

• Drive conservatively, especially over bumps (never off-road). Check periodically during use that all straps are

tight and bikes are secure.

• Do not use if any part of rack is damaged or missing. Contact R. A. Allen Co., Inc. for replacement parts.

1. Make sure that contact surfaces between car and rubber feet are

thoroughly clean and free of any dirt, and that all rubber feet remain

properly spaced during use.

2. Only thread top straps

through metal buckles as

shown in Drawing A. Never

thread straps through fist slot

in metal buckles as shown in

Drawing B.

Drawing A

3. Top hooks must be completely hooked over

solid metal edges at top of trunk, rear door, or

hatchback. Never hook to rain gutters, roof

racks, vertical rear glass or plastic moldings. Open

trunk/ hatch slightly for easiest attachment of

hooks. Be careful that hooks do not

bind when trunk/ hatch is opened or

closed.

4. Set length of top straps to position rack with its carry-arms inclined

slightly upwards (above the horizontal), and high enough to keep

bikes away from road and exhaust [for drawing of rack on

sedan style vehicle, see page 2 of instructions].

Note: It is

okay to position top

feet on glass;

NEVER install

rack with bottom

feet on glass.

6. Once rack is installed, bottom foot

assembly must be held against

vehicle in its completely open

position.

5. After length of top-strap is

set, tie a half-hitch knot at

each metal buckle as shown in

Drawing A.

7. Completely hook bottom hook to a

metal edge below the bumper or at the

bottom of the trunk.

Note: Make sure that bottom straps

are threaded through plastic buckles

only as shown in Drawing C.

Drawing C

Drawing B

3A. To secure top hooks on

vehicles without adequate clearance

at the top edge of rear trunk/ hatch: Un-

thread top straps from metal buckles and

open rear trunk/ hatch. Place top hooks

inside of vehicle (just inside of top edge of

rear trunk/ hatch). Carefully close rear

trunk/ hatch on top straps, making certain that

hooks do not bind between frame and rear

door. Important: with rear door closed, pull

top straps to bring hooks up tight against inside

of vehicle. Re-thread top straps through metal

buckles as shown in Drawing A. Mount rack

on vehicle.

Setting up

rack:

1. Fold out top-foot/ carry

arm assembly.

3. Completely fold out

bottom-foot assembly.

2. Insert pins at ends of

wire struts into holes in top

foot assembly.

8. Completely tighten bottom strap by pulling on free

end of strap until elastic portion of strap is completely

stretched. After straps are tightened, tie a half-hitch knot in

each strap near the buckle.

1 2

Inhaltsverzeichnis

Seite 1 - Model103A Bike Rack

AllenModel103A Bike RackEnglish InstructionsPg. 1B.Mounting rack on vehicle:Caution: Use Allen 103A only in accordance with local motor vehicle and tr

Seite 2 - Model 103A Bike Rack

AllenModel 103A Bike RackEnglish InstructionsPage 2.C.Alternate method #1 for Bottom Strap:Use if there is no metal edge below bumper for attachment o

Verwandte Modelle: 103A

Kommentare zu diesen Handbüchern

Keine Kommentare

Allen-sports 103AB Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Fahrräder Allen-sports 103AB herunter. Allen Sports 103AB User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 103A

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Fahrräder Allen-sports 103AB