Allen-sports 640RR Bedienungsanleitung PDF herunterladen

Allen

Model 640RR Instructions

English Instructions

Pg. 1

Caution: Use Allen 640RR only in accordance with local motor vehicle and traffic regulations.

• Install rack and load bicycles only at a safe distance away from moving traffic.

• Make sure that all of rack and bicycles are kept at a safe distance from road and hot exhaust.

• Remove rack from car or fold carry arms down when not in use.

WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury - do not

use rack on any vehicle on which it can not be properly mounted as described in this instruction sheet.

• Rack should only be used on vehicles with 2” receiver hitches.

•

Bikes must be tied to rack using tie-downs, or additional straps if necessary.

• Check periodically during use that all bolts and pins are tight, and that rack and bicycles are secure.

•

Never carry more than 4 bikes (max. capacity: 140 lb.) - no tandems, mopeds, or recumbents. Car tail lights must remain visible.

•

Never use on trailers or front of vehicle.

• Drive conservatively, especially over bumps (never off-road).

• Do not use if any part of rack is damaged or missing. Contact R. A. Allen Co., Inc. for replacement parts.

Parts:

- 1 - 3/8” x 3” Bolts

Tools required: 2 - 9/16” Wrench & 2 - 3/4” Wrench;

or 2 - Adjustable Wrenches

- 3 - 3/8” Nylon Insert Lock Nuts

- 1 - 1/2” Nylon Insert Lock Nut

- 1 - Base Post w/

Quick Release Pin

- 1 - 1/2” No-Wobble Bolt

1 - Upper Arm

Assembly

Assembling Rack:

Insert lower portion of RR Post (end

with the holes further apart) into Base

Post. Line up Holes A and B. Insert

1 - 3/8 x 3” bolt through this hole and

thread 1 - 3/8” Nylon Insert Lock Nut

onto the end of bolt. Do not tighten

until Step #2.

Insert Upper Arm Assembly into upper portion of RR

Post, lining up the holes in each part. Insert 3/8 x 2

1/2”” bolt through each hole and thread 3/8” Nylon

Insert Lock Nut onto the end of each bolt. Tighten

nut and bolt very firmly using 9/16” Wrenches.

Note: Upon completion both parts should be firmly

joined together.

Step #1:

Step #2

Step #3:

- 1 - RR Post

- 2 - 3/8” x 2 1/2” Bolts

1 - 70” Strap and

Buckle

HOLE A

HOLE B

Pivot RR Post into an upright

position so that Pop-Up Pin snaps

into place. Install Quick-Release

Pin. Tighten 3/8” nut and bolt very

firmly using 9/16” Wrenches.

Important: Whenever

Rack is in an upright position,

Quick-Release Pin must be

completely snapped in place

as shown above.

1 2

Inhaltsverzeichnis

Seite 1 - Model 640RR Instructions

AllenModel 640RR InstructionsEnglish InstructionsPg. 1Caution: Use Allen 640RR only in accordance with local motor vehicle and traffic regulations.• I

Seite 2 - Model 640RR Bike Rack

AllenModel 640RR Bike RackEnglish InstructionsPage 2.G.Loading bicycles onto rack:1. Remove all loose items from bikes (pumps, bags, etc.) and che

Kommentare zu diesen Handbüchern

Keine Kommentare

Allen-sports 640RR Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für Fahrräder Allen-sports 640RR herunter. Allen Sports 640RR User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für Fahrräder Allen-sports 640RR